在線留言|
您好，歡迎來到 濟南萬中電動扳手有限公司網站！
服務熱線： 400-117-8816
13406879330
13406879330
扭剪扳手,扭剪螺栓專用扳手,扭剪電動扳手,扭剪槍生產廠家
扭剪扳手,扭剪螺栓專用扳手,扭剪電動扳手,扭剪槍生產廠家
1、接通電源前應先查看電源電壓是否與本國產品銘牌相符，是否有接地裝置。當電源電壓超出+10%時應采取穩壓措施，否則會影響控制精度。接地不良易造成事故。
1. Before connecting the power supply, check whether the power supply voltage matches the nameplate of the domestic product and whether there is a grounding device. When the power supply voltage exceeds+10%, voltage stabilization measures should be taken, otherwise it will affect the control accuracy. Poor grounding can easily cause accidents.
2、工具使用的環境溫度為-10℃-40℃，過高過低會影響控制精度。
2. The ambient temperature for tool use is -10 ℃ -40 ℃, too high or too low can affect control accuracy.
3、被擰螺栓的初始扭矩不得大于工具的額定扭矩的70%。螺栓達到額定扭矩后不得重?cái)Q。
3. The initial torque of the tightened bolt shall not exceed 70% of the rated torque of the tool. Do not tighten the bolt again after reaching the rated torque.
4、工具用于拆卸螺栓時，其扭矩不得大于額定扭矩值。一般情況下，不是本扳手?jǐn)Q緊的或銹蝕嚴重的螺栓，不宜用本扳手拆卸，以免造成工具損壞。
4. When tools are used to disassemble bolts, their torque must not exceed the rated torque value. In general, bolts that are not tightened with this wrench or severely corroded should not be disassembled with this wrench to avoid tool damage.
5、變換旋轉方向時，必須待電機停止轉動后進行，嚴禁在運轉中撥動正反開關。
5. When changing the direction of rotation, it is necessary to wait until the motor stops rotating, and it is strictly prohibited to toggle the forward and reverse switches during operation.
6、當扳手自動停止后即可松開開關（如果不斷開開關，過5秒鐘扳手就會自行啟動）待4-5秒后再進行開動扳手，否則扳手不能啟動。
6. After the wrench stops automatically, you can release the switch (if you keep opening the switch, the wrench will start on its own after 5 seconds). Wait for 4-5 seconds before starting the wrench, otherwise the wrench cannot start.
