數顯扭力扳手校準流程
Calibration process of digital display torque wrench
1、使用扭力扳手校驗儀前，先檢查儀器是否有點。如果電量不足事需要充電或者在充電的時候進行校準。
1. Before using the torque wrench to calibrate the instrument, check whether the instrument has any points. If the battery is insufficient, it needs to be charged or calibrated during charging.
2、將被測物的方形探頭放入測試儀的方孔中，用被測物另一端的手柄在高度調節塊上方（如果長度不夠，可以整套自由調整裝載裝置）。
2. Put the square probe of the tested object into the square hole of the tester, and place the handle at the other end of the tested object above the height adjustment block (if the length is not enough, the loading device can be adjusted freely in a whole set).
3、打開電源開關，顯示的扭矩值為零，如果不為零，按復位鍵復位扭矩值。
3. Turn on the power switch and the displayed torque value is zero. If it is not zero, press the reset key to reset the torque value.
4、測試前需設置上下限值、小存儲值、小峰值保持值、自動峰值時間、自動關機時間、重力加速度等。
4. Before the test, the upper and lower limit values, small storage values, small peak holding values, automatic peak time, automatic shutdown time, gravity acceleration, etc. shall be set.
①、上限設置：用戶設置上限，根據需要自由設置，達到上自動聲光提示，上限不高于滿量程。
① Upper limit setting: the user can set the upper limit freely according to the needs. When the upper limit is reached, it will be automatically prompted by sound and light. The upper limit is not higher than the full scale.
②、下限設置：用戶設置下限，可根據需要自由設置。當達到下，自動燈會提示。下限不得高于設定的上限。
② Lower limit setting: the user can set the lower limit freely as required. When the lower limit is reached, the automatic light will prompt. The lower limit shall not be higher than the set upper limit.
③、小存儲值設置：用戶根據存儲需要設置小存儲值，小于該值的數據將不被存儲。
③ . small storage value setting: the user sets a small storage value according to storage needs. Data smaller than this value will not be stored.
④、小峰值保持值設置：用戶需要根據峰值自由設置自動峰值測量，小于該值的數據不會被峰值保存。
④ Setting of small peak holding value: the user needs to freely set automatic peak measurement according to the peak value, and data smaller than this value will not be saved by the peak value.
⑤、自動測峰時間設置：用戶可以根據自動測峰狀態下峰值需要保持的時間，在1秒到99秒之間自由設置時間。
⑤ Automatic peak measurement time setting: the user can freely set the time between 1s and 99S according to the time that the peak needs to be maintained in the automatic peak measurement state.
⑥、自動關機時間設置：在無操作狀態下，自動關機時間可以在0分鐘到9分鐘之間自由設置（設置為0分鐘時，表示取消自動關機）。
⑥ Automatic shutdown time setting: under no operation state, the automatic shutdown time can be freely set between 0 minutes and 9 minutes (when set to 0 minutes, it means to cancel the automatic shutdown).
⑦、重力加速度設置：用戶可以根據當?shù)氐奈恢迷O(shè)置重力加速度值。本機默認值為 9.794。
⑦ Gravity acceleration setting: the user can set the gravity acceleration value according to the local location. The default value of this machine is 9.794.
⑧、恢復初始設置：用戶操作不當或多次更改數據后出現混亂，可通過此設置將1到7的數據恢復到出廠狀態。
⑧ Restore the initial setting: if the user operates improperly or changes the data for many times, the data from 1 to 7 can be restored to the factory state through this setting.
The above is the detailed introduction of the electric wrench for torsion shear. I hope it will help you. If you have any questions, please contact us. We will provide you with services with a professional attitude http://m.hkystar.com
