在線留言|
您好，歡迎來到 濟南萬中電動扳手有限公司網站！
服務熱線： 400-117-8816
13406879330
13406879330
扭剪扳手,扭剪螺栓專用扳手,扭剪電動扳手,扭剪槍生產廠家
扭剪扳手,扭剪螺栓專用扳手,扭剪電動扳手,扭剪槍生產廠家
1、螺栓直徑的大小對控制精度有一定的影響，施工中應用相同型號的螺栓連接付來標定扭矩值，而且使用一段時間后還應進行檢驗校定。
1. The size of the bolt diameter has a certain impact on the control accuracy. During construction, the same type of bolt connection should be used to calibrate the torque value, and after a period of use, it should also be inspected and calibrated.
2、工作前應開機空轉3-5分鐘。操作中如發現電機火花大，聲音異常，扭矩不穩定時，應立即停機檢查，切勿帶病工作。
2. Before starting work, the machine should be turned on and idle for 3-5 minutes. If there is a large spark, abnormal sound, or unstable torque in the motor during operation, the machine should be stopped immediately for inspection. Do not work with a problem.
3、定期清洗和更換油脂，一般在工作5000次后，應進行一次清洗加油，以延長使用壽命。
3. Regularly clean and replace grease. Generally, after 5000 operations, a cleaning and oiling should be carried out to extend the service life.
4、主機上的電源開關，碳刷，控制儀上的保險絲等均屬易損件，容易引起故障，應經常檢查，及時更換。
4. The power switch, carbon brush, and fuse on the controller on the host are all vulnerable parts that can easily cause malfunctions. They should be checked regularly and replaced in a timely manner.
5、使用中如發現工具上的螺釘松動，應及時緊固。
5. If the screws on the tool are found to be loose during use, they should be tightened in a timely manner.
6、搬運工具時不可提拉電纜線，并注意輕拿輕放，防止震動和摔碰。不用時應放在通風干燥處。如發現受潮應及時進行干燥處理。不可與酸、堿等有害物質氣體接觸或存放在一起。
6. When transporting tools, do not lift the cables and handle them gently to prevent vibration and impact. When not in use, it should be placed in a ventilated and dry place. If moisture is found, it should be dried in a timely manner. Do not come into contact with or store together with harmful substances such as acids, alkalis, etc.
